I have tons of ideas to share with you all yet but be patient as I have to work around customers builds and there's only so many days in a week and no cloning machines on ebay!
I keep getting asked to do customers interiors but really do not have the time thats why I'm showing you what I'm doing to my Kalifornia so you can have a go. More soon |
Perhaps its time to team up with a trim shop who could offer a "standard" trim option for the SWB. That would allow you do what you are best at , body fitting, paint prep, paint and final finish.
Just a thought, as you seem to be very busy! |
Would be good if anyone knows a trimmer who can also fabricate parts?
|
The guys who did my interior but the frame and centre console, secret flap etc. They mainly seem to do luxury coaches, camper vans etc. Seem happy to be creative and their trimming and leather work is good. Based near Andover.
Ken Fernando klfautomotive@btconnect.com |
Quote:
http://www.rodsnsods.co.uk/forum/top...hop-week-32177 Good luck, Paul. :) |
Looks better in daylight. Really messy area now but as the saying goes ..you have to break some eggs to make an omelette
http://i64.photobucket.com/albums/h1...psw2cn9mev.jpg |
Looks good.
I'm fiddling about with dashboard changes on mine. Not as much change as yours but hopefully enough to make a difference. I've only done the passengers side air vent so far, but an MX5 eyeball can be persuaded to fit in the original Z3 frame, keeping the flap closing slide. I'll put some pictures on my thread tomorrow when the mastic hardens. Bob. |
Id like to see that. Was not sure what to do with side vents.
|
Today I wanted to cut off the rear roll over bar supports they stick up and look dumb.
http://i64.photobucket.com/albums/h1...ps8fd2vfx2.jpg |
I made a protective shield (ali sheet with a hole cut in it) and proceeded to chop it off.
http://i64.photobucket.com/albums/h1...psjpisfxut.jpg I think I will have to cut lower though once the seatbelt is removed. |
The inertia reel seat belts are the next part to replace otherwise you get a lump in the carpet or material behind the seats. I have replaced these with a set of fixed MG midget ones for £24 but I can sell the Z3 one on ebay for more. As I'm the only one going to drive the car, once they are adjusted they are good to use.
|
Nothing to do with interiors but Geoffs car is going back to him today so thought you might like to see it.
http://i64.photobucket.com/albums/h1...psa5x0ylwx.jpg http://i64.photobucket.com/albums/h1...ps54mj8hsz.jpg |
Now that's a classic, top work.
|
Lovely. I hope mine ends up as good when it's painted.
|
Quote:
http://www.ebay.co.uk/itm/Universal-...wAAOSwEetV9qAa http://i.ebayimg.com/00/s/ODAwWDgwMA...V9qAa/$_57.JPG Going further you could incorporate an Android tablet into the dash running OBD2 data interogation app and displaying analogue style gauges - I can see there are OBD2 apps on the Android store. You could then design any number of custom gauge styles/layouts you wanted and could change them on a whim.... The Torque OBD2 dashboard for Android does allow you to create custom dashboards - could be fun! |
Seller in Derby (or is that China, looking at the location on the feedback??). I wish this could be clarified by Ebay. I bought something a while ago advertised in a similar manner and it was indeed in UK (couldn't have even flown here from China in the time it arrived!). It puts a question mark on a lot of goods though.
|
Seller is based in China.
|
Some good advice for any driver with nine or more points in the ad too, if you can read Chinenglish:
...it helps new driver of less experience to control the speed to avoid overspeed in some speed limit road section, but also it makes the driver read the data rapidly without transforming vision and keep the best watch state soberly... Says it all really. |
Quote:
|
Im sure the price speaks for the quality and the origin of this product!
|
All times are GMT +0. The time now is 12:28. |
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright Madabout Kitcars 2022