1iTim - Great to see the video clip of your car rolling out of the garage. :cool:
Good luck, Paul. :) |
Well its been a while. A couple of moves, job stress lowering a little I'm planning on some more work on the car soon. Likely to do more updates in U-tube. nice to see your cars too.
|
https://www.youtube.com/playlist?lis...le&gl=US&hl=en
car has hydraulics and all now. I cranked it over last weekend with my supercapacitor bank, monday will see it fuelled and actually started and driven down the driveway, God willing. all the best, Tim |
Have you got a photo of your supercapacitor bank ? How long can you crank the engine on a single charge ?
|
Quote:
I tested the circuit on free modeling software and it pulls about 300A from zero V, so i bought a 120a breaker that i have in series with the tiny Li battery i have. It cranks over for 3 -4 seconds taking the voltage from 13.5 down to 10. then the capacitors charge from the battery in seconds (30 or so) for another go. Since my 948 cc is still running its generator not an alternator it could still be hand cranked, so i think the power is adequate. I've just stuffed something up and it wont spark at the moment. I only have videos and have not yet posted the unsuccessful cranking vid. the rapid charge from low voltage is also taxing the capacitors over-voltage circuitry and i may have difficulty there. (i also anticipate problems running at night) The best bit is that the caps and Li battery weigh in at less than a kilo. |
photos
4 Attachment(s)
attempting upload of photos as photobucket is not working for me anymore.
Tim |
Tim - Whilst you appear to have less room to work in than I had, at least you’ve got a roof!
http://www.madabout-kitcars.com/foru...5&d=1578887163 Hope ‘life’ settles down and you get to spend a bit more time on the car. Good luck, Paul. :) |
[/B]
Quote:
Can I just check please, you are using 300 lb springs? Are they going to be a bit stiff considering the car will be much lighter than Herald? Thank you. |
Ditto the above. I started with Vitesse 230lb front springs (car weighed 680kg with straight six up front) and couldn't go above 50mph without the front wheels bouncing off the road surface. A switch to Spitfire 180lb springs on Gaz ride/height adjustable shocks set to the second softest 'click' resulted in the front wheels staying in contact with the road and made for a much faster car in the real world.
330lb springs might give you an edge on the race track, but they might just leave you in a hedge on the road... |
Quote:
Thank you. |
Hi Deni, 180lb/in are quoted as 'standard' front springs for the Spitfire 1500, and were selected to work in combination with a rear swing spring and 7/8" front anti-roll bar.
I found them to give the best ride and handling compromise on my Spyder, even though I had a fixed rear spring, albeit with four leaves removed to soften the back end sufficiently given the much reduced weight over my Vitesse donor. Their part number is usually either TKC1881, TKC1884 or GSV1030, and their 'weight' spec tends to vary with supplier - Rimmers say 167lb/in for the GSV1030 while other sellers say 180lb/in for the same part number. As you say, Rimmers also have their GSV1030UR, which is shorter and rated at 200lb/in, and if you like a firm ride and the roads you're going to drive on are really smooth then you could give them a go. Oh, and if you use standard length springs you'll definitely need to fit height adjustable shocks or the nose will sit far too high. Anyway, here are some links to the '180lb' springs, and a useful website regarding setting up a small-chassis Triumph for the best handling. Just bear in mind that your car will be much lighter so you'll have to see what works best through trial and error. https://www.ebay.co.uk/itm/TRIUMPH-S...4AAOSw7NNT2koF https://rimmerbros.com/Item--i-GSV1030 http://auskellian.com/paul/links_fil...ents.htm#front Best of luck getting your car set up. |
Thanks Mr.T, that makes sense now. I assumed that you had bought the uprated springs...:smile: Thanks for the links too, it is much appreciated.
|
Quote:
Ok re reading that, maybe I did go 300 and might need to change... but they weren’t that expensive but needed to be much shorter than standard. |
3 Attachment(s)
So the work recently has been aluminium bulkhead and stuff:
http://www.madabout-kitcars.com/foru...0&d=1593326055 http://www.madabout-kitcars.com/foru...1&d=1593326055 http://www.madabout-kitcars.com/foru...2&d=1593326055 Now the bulkhead is in, I can put the regulator and wiring loom in. |
Lucas electrical...
Hi all,
It’s all wired up (dodgily and with no dashboard in place, and front/mid loom only, not rear or headlight loom yet) and starts fine now. However, the ignition light that should go out when the revs come up actually gets brighter with more revs. So the dynamo is working, but with no regulation. That’s bizarre. I did ‘flash’ the dynamo, it’s positive earth like it was originally. Have I done something wrong? Has something busted? It worked ok before tear down which was admittedly many years ago... Tim |
It sounds like your ignition light wire might be shorting out somewhere along its length.
Try disconnecting the wire at the generator and see if the light still comes on when you switch the ignition on. If it comes on it's shorting somewhere. I'm not certain that will work with a positive earth system but it should't cause any damage if you try it. Some useful info here - https://www.howacarworks.com/ignitio...-warning-light |
Found it and fixed it. I had extended a wire to reach the ignition solenoid but had not insulated it and it was earthing. Thanks mr T.
|
Glad I could help :)
|
Drivable!
Hi all, another update, most records are video now and available publicly on u tube. You all can hear it starting on the supercapacitor/lithium ion setup that i have on it. Several start attempts one after the other and no dramas.
I drove it to the end of my driveway which was a very exciting 10m (m for meters not miles) drive! heres a picture of it at the top of the drive. https://www.instagram.com/p/CDSVxo-H..._web_copy_link https://www.instagram.com/p/CDSVxo-H...on_share_sheet https://external.fbne6-1.fna.fbcdn.n...ALoLsV8H4231Ou now to do passenger seat, front and rear wiring, oh, and get a mod- certifying engineer to review before I bond the body on... stay safe, madabouters. T |
Good work, exhaust has a nice burble to it - that should grab the neighbours attention! (sorry for the bad TV reference).
|
All times are GMT +0. The time now is 15:47. |
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright Madabout Kitcars 2022