Has anyone built a 3 wheeler?
 

Cycle cars fascinate me. When I was about six years old I had a ride in a Morgan Barrelback that must have stuck with me.
Recently, I was given the opportunity to purchase a shaft drive Honda V-Twin
and I'm considering building a BRA style replica.

Has anyone here ever built a three wheeler?

Thoughts..

There is a top quality three wheeler build here:

http://www.madabout-kitcars.com/foru...ead.php?t=3818

http://www.madabout-kitcars.com/foru...ight=Pembleton

This may help

Snap!

Ha ha great minds and all that ��

I've been all over that build thread before. Thanks guy's.
Here in the USA, 2CV's are hard to find. I'll thinking Honda V-Twin or Harley power. Preferably mated to a VW or Miata gearbox.
Also considering a Fiero or Chevette front suspension. The closest builds that I can find are the old BRA CX3 (Honda) or the JVA with a Harley. Tons of research to do. There was a Pembleton in Daytona owned to a fellow that I spoke to. He indicated that he was afraid to take it in the freeway. I believe he recently sold it. A little more Oomph for me will require a more powerful engine and perhaps a slightly longer wheelbase and front track.

Micky1mo has had dealings with them I think ..might be worth a message to him ....Penguin Speedshop were/are doing something similar too ..

I shall. Thanks LL!

Have you looked at the BR website?

BRA CX3 build plans are available, may go for it.

I've been communicating with Penguin Speed Shop on the Buckland.
No recent e-mails answered. I do fancy a Morgan F type replica.

According to a kit car mag Penguin were after selling the Buckland project. A superb 3 wheeler.

I was alerted to that possibility, however, Penguin mentioned to me in my last e-mail that they were looking for an investor. We'll see.
There is a complete unassembled kit in Texas and I may have a go look soon. I believe only one of maybe two in the USA.

Maybe I'll have to do a complete schrtch build.

I would go with the Buckland, at the right price and if you can find a engine.
But the BRA3cx plans would be a good start too. I wouldn't fancy taking any small 3 wheelers on a busy freeway, some low kit cars 7ish can be scary in any British town.
Good luck

Engine & gearbox not a problem. The 1.6 Kent engine was used in many TVR's. Decked, can easily be a 1.3 if desired. I have access to many of these. If I do have to do a scratch build, the bevelbox is the only issue right now.

You could modify a Ford Sierra diff. The Buckland has a chain drive from the diff to the rear wheel. Or use the bevel drive from a shaft drive motor bike. There was a great Steampunk trike in either '100% Bike' or its sister 'Trike' a while back. That had a Virago V twin in line, like in the bike and shaft drive to the rear wheel. That setup in a BRA would look great.

Yes, thinking of a Guzzi or Goldwing rear & diff. With the 4 speed transmission + reverse. Only need to fabricate a driveshaft and appropriate carrier bearings.

Getting there identifying the needed components.

Now you know what you are going to do get on with it and send us pictures. Good luck!

Not quite ready just yet. At least the bodywork will not be a problem.
Saving pennies for the "Revival" next month. Looking iffy at the moment though.

Was a former GRRC member for many years. Expensive to fly from the USA for events.

molleur Sorry but I have only just noticed this thread.:doh:

I think I still have a set of plans and a build manual for the BRA3 or something similar any-way.

I'll try and locate them over the next few days. :smile:

Appreciated! You do know I'm in Florida.

You'll be paying the postage then :lol::lol:

micky1mo

have you found them yet ?

Gladly!

I'v now tracked them down to a friends garage.
I'm just waiting for him to return them. :pop2:

Super! Thamks..

Are they scannable /copyable ( is that a word) wouldn't mind a set myself please :-)

Finally located the plans for a BRA CX3.
Which is a 2CV powered, 2 seater, 3 wheeler.

There is a lot more to them than I remembered, I have the plans which consists of several full size sheets, cutting list, build CD's ect.

https://i.imgur.com/iuYSwl3h.jpg

All-in-all quite a package.

Looks like a lot of fun. Keep us informed.

The plans are for a CX3 (not a 2CV) which uses a CX500 motor and drive train.

When looking for the plans I also found CX500 engine/gearbox, rear wheel complete with swinging arm and drive shaft!!
Along with a more-or-less complete front wish-bone suspension assembly so I must have been serious about building one at some stage!!:eyebrows:

Your garage must be a bigger mess than mine. How do you have all that gear and not fall over it? Look a bit harder, you might find the chassis!

Fortunately a messy workshop is a busy workshop,
I have all that gear because I need it, I don't trip over it because most of it is stored on the shelf.
As for the chassis it was never lost just stored outside until needed.

http://i.imgur.com/YRK7NbGh.jpg

But that is a 2cv chassis without the bottom plating ?

I don't need another project ......I don't need another project ......I don't need another project ......I don't need another project ......I don't need another project ......I don't need another project ......

I have the Leighton body panel set, the chassis, engine, gearbox, front axle, converted single rear axle, hand brake, gear stick even the V5 and all for sale :biggrin1:

YOU DO NEED ANOTHER PROJECT :eusa_whistle: