Are you madabout kit cars      
 "We've Got Kit Cars Covered" Information about Madabout-Kitcars.com Contact Madabout-Kitcars.com         Home of UK kit cars - madabout-kitcars.com Various kit car write ups All the latest kit car news Kit car related and general discussion

Search
Manufacturers
Kit Cars
Kit Car Data sheets
Picture Gallery
SVA Knowledgebase
Clubs & Communities
Build cost estimator
Kit cars for sale
Knowledge Base 
KitcarUSA.com
Classic-Kitcars.com
 

Go Back   Madabout Kitcars Forum > Mad Build Area > Vintage and Classic Roadster Kit Car Builds

Vintage and Classic Roadster Kit Car Builds For Vintage and Classic era kit cars. Post your build reports, problems and progress here

Reply
 
Thread Tools Display Modes
  #321  
Old 26th March 2018, 20:31
peterux's Avatar
peterux peterux is offline
Senior Member
Enthusiast
 
Join Date: Mar 2005
Posts: 2,733
peterux is on a distinguished road
Default My baby is back at home.....

Over the weekend I found time to complete the repairs to the radiator cowl.

I finished re-enforcing the back of the cowl with glass mating and resin and then ground it flat with a flap disk in my angle grinder.

Painting by Sabrebuilder, on Flickr

After I sanded down the front I found the damage was much worse than I first thought. It had already been repaired before being broken again. I dug out all the cracked gelcoat and filled it with GRP filler.

Painting by Sabrebuilder, on Flickr

I also created a raised 'plinth' for the badge....

Painting by Sabrebuilder, on Flickr

I then retrieved the front wings that have been hanging from the garage rafters for the last few years. They were covered in dust and spiders poo so I gave them a quick wash.

Painting by Sabrebuilder, on Flickr

Today, we collected the body tub and doors from the painters, but first we loaded up the front wings.

Painting by Sabrebuilder, on Flickr

And then the trailer was hitched up for the journey back home.

Painting by Sabrebuilder, on Flickr

Painting by Sabrebuilder, on Flickr

And it's now tucked up safely back in my garage at home.

Painting by Sabrebuilder, on Flickr

Happy days


....peter
Reply With Quote
  #322  
Old 4th April 2018, 19:33
peterux's Avatar
peterux peterux is offline
Senior Member
Enthusiast
 
Join Date: Mar 2005
Posts: 2,733
peterux is on a distinguished road
Default Fuel level sender mods

A few weeks back I mentioned that I will give an update on the Fuel level sender modifications I've been working on.

This is the Ford combined 'lifter pump' and fuel level sender that fits the Granada fuel tank installed in the Sabre. But the Ford sender's resistance is not compatible with the ETB Fuel gauge that I have bought.

Fuel Level Sender by Sabrebuilder, on Flickr
(sorry about the poor quality photo's)

This is the ETB fuel level sender. Luckily, the full range from Empty to Full is covered by a 90 degree sweep which is the same as the Ford sender. Also, the RTB sender's variable resistance part is easily unbolted.

Fuel Level Sender by Sabrebuilder, on Flickr

Before dismantling the Ford sender I marked the Full and Empty positions. It was easy to remove the Ford variable resistor by just bending back a couple of tabs.

Fuel Level Sender by Sabrebuilder, on Flickr

I then mounted the ETB rheostat to the Ford support leg using M6 screws and some aluminium tube spacers. A very fiddly job!!

Fuel Level Sender by Sabrebuilder, on Flickr

And here is a side view of ETB sender mounted on Ford fuel tank unit. In the Full position.

Fuel Level Sender by Sabrebuilder, on Flickr

It seems to work OK so just need to wire it up and make sure the gauge reads correctly; and then make sure it fits OK in the tank.

Another little job ticked off the plan

.....peter
Reply With Quote
  #323  
Old 5th May 2018, 19:12
peterux's Avatar
peterux peterux is offline
Senior Member
Enthusiast
 
Join Date: Mar 2005
Posts: 2,733
peterux is on a distinguished road
Default Nearly done....

Well the final three body panels are being prepped for paint. The front wings and boot lid have been stripped of the old paint and primed ready for flatting.

Front wings and bootlid by Sabrebuilder, on Flickr

Should be finished next week.

I then just need to find the time to start the re-assembly

...peter
Reply With Quote
  #324  
Old 5th May 2018, 20:09
Barber's Avatar
Barber Barber is online now
Senior Member
 
Join Date: Apr 2016
Location: Camberley
Posts: 653
Barber is on a distinguished road
Default

There is something special about those cats.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +0. The time now is 15:37.

copyright madabout-kitcars.com 2000-2018
terms and conditions | privacy policy