Are you madabout kit cars      
 "We've Got Kit Cars Covered" Information about Madabout-Kitcars.com Contact Madabout-Kitcars.com         Home of UK kit cars - madabout-kitcars.com Various kit car write ups All the latest kit car news Kit car related and general discussion

Search
Manufacturers
Kit Cars
Kit Car Data sheets
Picture Gallery
SVA Knowledgebase
Clubs & Communities
Build cost estimator
Kit cars for sale
Knowledge Base 
KitcarUSA.com
Classic-Kitcars.com
 

Go Back   Madabout Kitcars Forum > Mad Build Area > Tribute Automotive Builds

Tribute Automotive Builds Discuss your Tribute kit build

Reply
 
Thread Tools Display Modes
  #1  
Old 13th January 2019, 19:01
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default Z3 Immobilised

Important edit before you read this thread-
It had nothing to do with the immobiliser.


My car lives outside and is subject to a lot of condensation. I went out to use it yesterday and it will start but not run. Clearly a problem with the immobiliser circuitry. (Subsequently- AA diagnostics said it is an immobiliser problem but we suspect the cam sensor) Depressing the clutch pedal (some cars have switches) and replacing the key fob battery (the detector ring on the ignition switch shouldn't need it) have no effect.
I'm now running a fan heater and dehumidifier in the car in the hope that whatever is damp and shorted will dry out and unshort.
I've read a lot of forums on "deleting" the immobiliser- anyone on here have any advice please?

Last edited by IanA; 26th February 2019 at 15:21.. Reason: AA diagnostics said it is an immobiliser problem.
Reply With Quote
Available from eBay
  #2  
Old 13th January 2019, 19:29
Jaguartvr's Avatar
Jaguartvr Jaguartvr is offline
Senior Member
 
Join Date: Jan 2014
Location: Egham, Surrey
Posts: 1,780
Jaguartvr is on a distinguished road
Default

i would have thought the immoboliser would have stopped it from starting at all.
Reply With Quote
  #3  
Old 13th January 2019, 21:05
WorldClassAccident WorldClassAccident is offline
Senior Member
 
Join Date: Nov 2011
Posts: 3,558
WorldClassAccident is on a distinguished road
Default

Check the wiring to the 'ring' around the ignition key. Mine is loose and if the ring falls off and dangles on the wires the car won't start when I put the key in. If you can get the demist etc working that matches the symptoms I get from a dodgy ring.
Reply With Quote
  #4  
Old 13th January 2019, 21:14
froggyman's Avatar
froggyman froggyman is offline
Senior Member
 
Join Date: Dec 2011
Location: Devon
Posts: 550
froggyman is on a distinguished road
Default

A 'dodgy ring' is more likely to caused by a curry than condensation!
Reply With Quote
  #5  
Old 13th January 2019, 21:28
Lucky@LeMans Lucky@LeMans is offline
Senior Member
 
Join Date: Aug 2012
Posts: 2,142
Lucky@LeMans is on a distinguished road
Default

I can't be much help other than to say my Z3 had a Thatcham system fitted that was a total pain as it was always going off for no reason. Even if you walked passed the car it would start bleeping and making noises. There is a very good mobile auto electrician I use, he came round and removed the whole thing in 25 minutes. Now I'm back with the standard BMW system and its fine. That was the best £45 I have spent on the car !
Reply With Quote
  #6  
Old 13th January 2019, 21:54
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

The EWS II system on the Z3 (and other BMWs) is a "Drive-Away Protection" system. Switching on the ignition (which could be done easily by hot-wiring the switch or screw-drivering the key barrel) initiates the full start sequence with alarm off, fuel pump up to pressure, ignition made live, etc.
When the key/barrel is turned to start, the detector ring needs to read the key when the starter turns. Various codes are swapped at that time. If that is not successful, the fuel pump and ignition are switched off and the engine dies.
The car's electronics are programmed to read the right key. My correctly cut key turns the barrel and ignition switch and starts the engine but the code is absent so no more sparks or juice.
The two connecting wires on the detector ring (per WCA) disappear into a sleeve in the steering column shroud. My best bet is probably to follow them to exercise any connectors and break out the WD40.
Reply With Quote
  #7  
Old 13th January 2019, 22:21
peterux's Avatar
peterux peterux is offline
Senior Member
Enthusiast
 
Join Date: Mar 2005
Posts: 3,074
peterux is on a distinguished road
Default

IIRC there is a very small connector right on the back of the ring antenna.
You could start there but get some contact cleaner rather than WD40.
Have a look at the pictures in here.....

https://www.ecstuning.com/b-genuine-...a/61356965426/
Reply With Quote
  #8  
Old 13th January 2019, 22:26
WorldClassAccident WorldClassAccident is offline
Senior Member
 
Join Date: Nov 2011
Posts: 3,558
WorldClassAccident is on a distinguished road
Default

When my ring drops off the steering column it dangles on two wires. I put the key in the ignition and everything seems fine but the car won't even try to start. The ignition lights etc seem fine but nothing when I turn the key. This seems similar to the symptoms you are describing which is why I suspect the same cause.

Somewhere the link between the key, the ring and the cars 'brain' there is a break.

You have replaced the key fob battery so we assume that is okay.

Is your ring firmly attached? Mine seems to be a relatively loose push fit which is why it sometimes falls off and how I discovered the issue. Try giving it a wiggle and if that works it suggests a loose wire or connection.

Other than that, I guess your are buggered :-)
Reply With Quote
  #9  
Old 13th January 2019, 23:26
peterux's Avatar
peterux peterux is offline
Senior Member
Enthusiast
 
Join Date: Mar 2005
Posts: 3,074
peterux is on a distinguished road
Default

Quote:
Originally Posted by peterux View Post
IIRC there is a very small connector right on the back of the ring antenna.
You could start there but get some contact cleaner rather than WD40.
Have a look at the pictures in here.....

https://www.ecstuning.com/b-genuine-...a/61356965426/
Actually, thinking about this problem so more, I don't think you have an EWS problem. The EWS II module interrupts the supply to the starter motor so assuming you actually get the engine started, then I don't think it can be the EWS.
Sounds more like a lack of fuel or water mixed with the fuel. Try chucking a can of fresh fuel in the tank? Or maybe a blocked fuel filter?

Failing that you need to get the codes read as it could be any sensor like the crankshaft sensor being intermittent.
Reply With Quote
  #10  
Old 14th January 2019, 13:57
Jaguartvr's Avatar
Jaguartvr Jaguartvr is offline
Senior Member
 
Join Date: Jan 2014
Location: Egham, Surrey
Posts: 1,780
Jaguartvr is on a distinguished road
Default

Check the wires where they would have entered the boot. They are very prone to fraying and snapping. Mine had a few broken wires which affected the central locking, not sure if it will have anything to do with your problem but worth checking.
I still don't think the car would start at all if it was anything to do with the immobiliser.
Reply With Quote
  #11  
Old 15th January 2019, 14:00
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Quote:
Originally Posted by Jaguartvr View Post
i would have thought the immoboliser would have stopped it from starting at all.
Correct!!! I proved it by trying a "dead" key which I'd had cut but not programmed. It would not start the engine unless it was used within a short time of starting with the programmed key. That confused me briefly.
So- the problem is not in the immobiliser.

Last edited by IanA; 6th February 2019 at 15:28.. Reason: AA diagnostics now say it is an immobiliser problem
Reply With Quote
  #12  
Old 15th January 2019, 14:04
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Quote:
Originally Posted by peterux View Post
Actually, thinking about this problem so more, I don't think you have an EWS problem...Failing that you need to get the codes read as it could be any sensor like the crankshaft sensor being intermittent.
The only code that persists is P0443 which relates to the fuel vapour system- I understand that it may only affect fuel consumption, not affect the running.

If it were cam or crank sensor, I'd expect to see P0340 or similar after each start. There's nothing obvious that stops the engine running. The shut-off sounds like an ignition cut. Fuel system feels OK because the engine starts instantly and strongly.
Reply With Quote
  #13  
Old 15th January 2019, 14:09
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Quote:
Originally Posted by IanA View Post
... Switching on the ignition (which could be done easily by hot-wiring the switch or screw-drivering the key barrel) initiates the full start sequence with alarm off, fuel pump up to pressure, ignition made live, etc.
When the key/barrel is turned to start, the detector ring needs to read the key when the starter turns. Various codes are swapped at that time. If that is not successful, the fuel pump and ignition are switched off and the engine dies.
I got that info from other BMW forums relating to other models (and personal experience of it on a Ford Escort Cabrio) but it does not apply to my Z3. If the immobiliser is working, anything turning the barrel/ignition switch apart from the correctly programmed key does not start the engine.

Last edited by IanA; 15th January 2019 at 14:17..
Reply With Quote
  #14  
Old 15th January 2019, 14:15
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Quote:
Originally Posted by peterux View Post
IIRC there is a very small connector right on the back of the ring antenna.
Thanks for the suggestion. I have solved previous problems on other cars by "exercising" every plug/socket in sight.

See my other post which rules out the immobiliser.

The immobiliser ring on my car does not have a plug there- the wires are captive into the unit:

Last edited by IanA; 8th February 2019 at 14:43.. Reason: AA diagnostics said it is an immobiliser problem but we suspect the cam sensor
Reply With Quote
  #15  
Old 15th January 2019, 19:46
WorldClassAccident WorldClassAccident is offline
Senior Member
 
Join Date: Nov 2011
Posts: 3,558
WorldClassAccident is on a distinguished road
Default

See where the two green wire connect to the ring? That ring now falls off the steering column occasionally (thanks Dan) and although the two wire appear perfectly connected, the car wont start. Push it back onto the column and we are away.

I think you should spray the wires with contact cleaner and anything else. Try wiggling etc. A small break can cause this stuff, my hood stopped working occasional for a similar cracked wire.
Reply With Quote
  #16  
Old 15th January 2019, 19:55
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Quote:
Originally Posted by WorldClassAccident View Post
...I think you should spray the wires with contact cleaner and anything else. Try wiggling etc. A small break can cause this stuff, my hood stopped working occasional for a similar cracked wire.
I've done both and the "live" key/"dead" key difference proves that the immobiliser ring is picking up and forwarding the code.

Must have a look for that hood wire/microswitch to see if that's why the electric raise/lower failed.
Reply With Quote
  #17  
Old 21st January 2019, 17:03
IanA's Avatar
IanA IanA is offline
Senior Member
 
Join Date: May 2014
Location: Oxon
Posts: 1,118
IanA is on a distinguished road
Default

Battery is OK.
Fuses are OK.
Relays are OK- pulled, no rattles and replaced.
Fuel pump is OK- healthy squirt from the fuel rail.
Found a small split in the breather pipe junction just downstream of the MAF- taped that up like this:



Other air pipes look OK.
Still starts strongly and then dies.
If it were a cam or crank sensor it wouldn't start.
No codes shown except the fuel evap P0443.
May have to resort to AA HomeStart.

Last edited by IanA; 8th February 2019 at 14:44.. Reason: AA diagnostics said it is an immobiliser problem but we suspect the cam sensor
Reply With Quote
  #18  
Old 21st January 2019, 21:45
WorldClassAccident WorldClassAccident is offline
Senior Member
 
Join Date: Nov 2011
Posts: 3,558
WorldClassAccident is on a distinguished road
Default

I have just re-read your original post. You said it starts and then immediately dies.

Everything I have contributed to this thread so far is complete bollocks then. I first read that it wouldn't start at all.

I will try to recover the situation...
Reply With Quote
  #19  
Old 21st January 2019, 21:56
WorldClassAccident WorldClassAccident is offline
Senior Member
 
Join Date: Nov 2011
Posts: 3,558
WorldClassAccident is on a distinguished road
Default

Let's start with first principals.

The engine needs fuel, air and a spark to ignite them.

You have checked that fuel squirts out so hopefully that is one point covered but we might reexamine this.

Air is simpler and if there are no major leaks then you are probably fine. I would still give the MAF sensor a good squirt of quick drying contact cleaner. It is just before the jubilee clip in your picture and cleaning mine took nearly 1/2 a second off the 20-80mph acceleration test.

This leaves electrics as the probably culprit. Unfortunately no-one understands electrics as you can't fix it with a hammer and gaffer tape.

So in summary, it is probably electrics but I have a niggling thought that fuel might play a part in it too.

It starts initially which means there is fuel, air and electrics.

It then dies which suggests one of the three has gone.

Air is pretty reliable so I am discounting that.
Electrics are unexplained but in my experience they either work or they don't and once they don't work then stay not working so I am holding back on that.
Fuel is necessary and is clearly there when the engine fires but possibly doesn't continue to flow so the engine dies.

Dr WCA delivers his diagnosis
Reply With Quote
  #20  
Old 21st January 2019, 23:31
Lucky@LeMans Lucky@LeMans is offline
Senior Member
 
Join Date: Aug 2012
Posts: 2,142
Lucky@LeMans is on a distinguished road
Default

Are you in the AA ?
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +0. The time now is 15:14.

copyright © madabout-kitcars.com 2000-2024
terms and conditions | privacy policy