Are you madabout kit cars      
 "We've Got Kit Cars Covered" Information about Madabout-Kitcars.com Contact Madabout-Kitcars.com         Home of UK kit cars - madabout-kitcars.com Various kit car write ups All the latest kit car news Kit car related and general discussion

Search
Manufacturers
Kit Cars
Kit Car Data sheets
Picture Gallery
SVA Knowledgebase
Clubs & Communities
Build cost estimator
Kit cars for sale
Knowledge Base 
KitcarUSA.com
Classic-Kitcars.com
 

Go Back   Madabout Kitcars Forum > Mad Build Area > Sammio Builds and discussions

Sammio Builds and discussions Sammio bodied car builds and specials

Reply
 
Thread Tools Display Modes
  #401  
Old 8th April 2015, 22:23
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

Cardboard or steel ummmm LOL

Last edited by swifty; 8th April 2015 at 22:27..
Reply With Quote
  #402  
Old 9th April 2015, 22:47
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

A little more progress made, finished the battery clamp made from 1.5mm stainless.

IMG_5260.jpg


Finished the screen mount machined on the cnc mill out of 1.5mm ally sheet, similar to what is fitted on the old Ferrari's. To make it easier to shape to the curves of the body i've annealed the ally to make it act like putty (very easy to bend in your fingers) this was done after the profile was milled. The annealing is easy to do with an acetylene torch first light the acetylene to give a sooty flame don't use the oxygen just yet, run the sooty flame over the ally surface covering in soot but not too thick as it takes longer to burn off now turn on the oxygen to give a blue flame and run this over the sooty surface about six inches off and don't stop the flame moving as the ally will melt very quickly, once the soot has burned off the ally will be at the correct temperature for annealing which i believe to be 700 degrees which is virtually the temperature ally melts, then leave to cool to room temperature don't quench as you will undo the annealing process.


IMG_5263.jpg

Machined lugs evenly spaced to bolt the screen to the mount. Made in two halves joining in the middle to make it easier to work with when shaping to the body.


IMG_5267.jpg

Jig made to curve and bend the trim or at least i hope it will.


IMG_5261.jpg

Mold made for the dashboard from oasis.



Well that's it for now see you all soon.

Last edited by swifty; 10th April 2015 at 19:34..
Reply With Quote
  #403  
Old 10th April 2015, 07:06
Paul L's Avatar
Paul L Paul L is offline
Senior Member
 
Join Date: Feb 2012
Location: Wembley, London
Posts: 5,056
Paul L is on a distinguished road
Default

Swifty - Clearly your "simple" screen support has taken a lot of clever work to make.

Your "eyebrow" dash is also going to look good sitting behind that screen.

Good luck, Paul.

PS
If I tried to work on my car with an acetylene torch I would probably end up burning my house down, along with the car.
Reply With Quote
  #404  
Old 10th April 2015, 07:20
8 Valve Ed 8 Valve Ed is offline
Senior Member
 
Join Date: Dec 2013
Location: Sunny Cumbria
Posts: 470
8 Valve Ed is on a distinguished road
Default

The acetylene flame is one way but you can do it with a blow lamp, have a thin splinter of pine wood and when the splinter blackens when touched onto the metal it's hot enough to anneal it, allow to cool slowly. A tip from a retired local shipyard worker.
Reply With Quote
  #405  
Old 10th April 2015, 08:46
garyh garyh is offline
Senior Member
 
Join Date: Jun 2011
Location: birchington, kent
Posts: 1,769
garyh is on a distinguished road
Default

What about a hot air gun?
Reply With Quote
  #406  
Old 10th April 2015, 17:38
8 Valve Ed 8 Valve Ed is offline
Senior Member
 
Join Date: Dec 2013
Location: Sunny Cumbria
Posts: 470
8 Valve Ed is on a distinguished road
Default

Maybe, for a small bit, never tried it... Not hard to test. Hint, I often anneal copper washers on the gas stove in the kitchen...
Reply With Quote
  #407  
Old 10th April 2015, 18:34
reneanglia reneanglia is offline
Senior Member
 
Join Date: Jan 2015
Posts: 168
reneanglia is on a distinguished road
Default

Quote:
Originally Posted by garyh View Post
What about a hot air gun?
No,air gun is nothing more as a glorified hairdryer.............
I have a professional hot air gun at work,it reaches about 650 degrees celcius at the glow head but the heathed piece of metal never reaches over 500 C.
The metal should be 700C.
Reply With Quote
  #408  
Old 10th April 2015, 19:26
8 Valve Ed 8 Valve Ed is offline
Senior Member
 
Join Date: Dec 2013
Location: Sunny Cumbria
Posts: 470
8 Valve Ed is on a distinguished road
Default

Quote:
Originally Posted by reneanglia View Post
No,air gun is nothing more as a glorified hairdryer.............
I use my glorified hairdryer to shrink shrinkwrap (only). Think it would frizzle hair a bit... LOL
Reply With Quote
  #409  
Old 10th April 2015, 19:32
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

Yep you need the ally up to 700 degrees to anneal, another way to tell when the temperature is correct is to smear a little liquid soap on the ally surface and when this goes black the temp is correct not sure if general liquid soap is ok as i was taught with the creamy industrial type but i suppose there's no harm in trying test piece.

Last edited by swifty; 10th April 2015 at 19:54..
Reply With Quote
  #410  
Old 12th April 2015, 20:15
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

This weekend i've been working on three jobs switching between them when i got bored.

IMG_5268.jpg

Molded the dash section with fiberglass over the oasis mold made earlier then glassed onto the dash board and covered in fiber filler.



IMG_5269.jpg IMG_5270.jpg

Finished off with body filler then flatten off ready for the under coat, the eyebrow trim now means a 100mm tachometer will comfortably fit behind the steering wheel area.


IMG_5271.jpg

Made good progress with the gearbox tunnel, made from 1.5mm ally sheet. I was going to roll the top surface but decided to leave it flat and possibly roll a separate piece to fit on top and see what it look like, one advantage with the flat top is that a small tray can be used to hold say a mobile phone.


IMG_5272.jpg

Cut the screen out to suit the body profile and started to bend the ally trim made earlier to follow the body profile and screen edge.




Well that's it for now see you all soon.

Last edited by swifty; 12th April 2015 at 20:57..
Reply With Quote
  #411  
Old 13th April 2015, 19:12
Paul L's Avatar
Paul L Paul L is offline
Senior Member
 
Join Date: Feb 2012
Location: Wembley, London
Posts: 5,056
Paul L is on a distinguished road
Default

Swifty - It is really starting to come together now.
Reply With Quote
  #412  
Old 13th April 2015, 19:30
EL PRIMER's Avatar
EL PRIMER EL PRIMER is offline
Senior Member
 
Join Date: Nov 2013
Posts: 143
EL PRIMER is on a distinguished road
Default

Dash bulge is lovely .
Reply With Quote
  #413  
Old 13th April 2015, 20:48
Thurcroft flyer Thurcroft flyer is offline
Senior Member
 
Join Date: Dec 2013
Location: thurcroft, Rotherham South Yorkshire
Posts: 196
Thurcroft flyer is on a distinguished road
Default

I think the screen will look super when done, really period.
Reply With Quote
  #414  
Old 15th April 2015, 20:37
davecymru's Avatar
davecymru davecymru is offline
Senior Member
 
Join Date: May 2011
Location: Somerset
Posts: 1,671
davecymru is on a distinguished road
Default

Great progress and I had exactly the same thoughts about a rolled vs flat dash top! TBH I've gone with flat for the time being and it's been very useful during the built to put things on, but that may change in time..
Reply With Quote
  #415  
Old 21st April 2015, 20:27
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

Not a lot of progress made due to the fact i've bought a 4x4 that lets say was not running perfect but due to this i got for a song, started to remove the engine to replace the piston rings and hopefully will be able to move on quickly.

Did get a chance to finish the screen mount and it looks the business, now looking at ways to age the look of the ally used to make the mount.

IMG_5281.jpg

Turned some nuts from ally, these are what hold the screen to the ally mount. Made to the same diameter as the lugs on the outside ally mount which helps the whole look of the screen mount.




IMG_5284.jpg

Rear view of the nut in place on the inside of the screen.



IMG_5293.jpg

Made a cover mirroring the shape to hide the center join, the screws are temporary for now as i think i will pop rivet the mount in place once the paint job is finished.



IMG_5282.jpg IMG_5289.jpg

Screen in place with the protective film still in place, the ends have been left slightly longer as i am toying with idea of may be machining a couple of end brackets but will live with how it is for now.


Well that's it for now see you all soon.

Last edited by swifty; 21st April 2015 at 20:36..
Reply With Quote
  #416  
Old 21st April 2015, 21:26
Paul L's Avatar
Paul L Paul L is offline
Senior Member
 
Join Date: Feb 2012
Location: Wembley, London
Posts: 5,056
Paul L is on a distinguished road
Default

Swifty - This really is going to be a very special car.

Although I can't believe you bought another project for your "spare" time.

Good luck, Paul.
Reply With Quote
  #417  
Old 4th May 2015, 10:07
swifty's Avatar
swifty swifty is offline
Senior Member
 
Join Date: Dec 2013
Posts: 839
swifty is on a distinguished road
Default

Very slow progress of late. Made a couple of ally brackets to support the screen ends.

IMG_5303.jpg IMG_5304.jpg

Attached to the body which i have slightly built up with fiber filler to give a flat surface to mount to.



IMG_5307.jpg

Made a rough cardboard template for the dash to work out what goes where, i intend on using 3mm ally sheet for the dash and having it powder coated. Have been playing around with the clocks to make a final decision before placing an order, does any body know of a good supplier of dash clocks?


Well that's it for now see you all soon.
Reply With Quote
  #418  
Old 4th May 2015, 10:39
phil9 phil9 is offline
Senior Member
 
Join Date: Mar 2012
Posts: 745
phil9 is on a distinguished road
Smile

great work swifty
Reply With Quote
  #419  
Old 4th May 2015, 11:14
Viatron Viatron is offline
Senior Member
 
Join Date: Apr 2012
Posts: 1,163
Viatron is on a distinguished road
Default

I got mine from Speedhut.com, good price and customisable and very easy to wire up.

Mac
Reply With Quote
  #420  
Old 4th May 2015, 12:17
1iTim's Avatar
1iTim 1iTim is offline
Senior Member
 
Join Date: Aug 2013
Location: Brisbane, Australia
Posts: 276
1iTim is on a distinguished road
Default

My herald came with white jaeger jobbies that look sweet but no tach. I'll wing it by ear....

Your fabrication is fabulous
T
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +0. The time now is 07:13.

copyright © madabout-kitcars.com 2000-2024
terms and conditions | privacy policy