Are you madabout kit cars      
 "We've Got Kit Cars Covered" Information about Madabout-Kitcars.com Contact Madabout-Kitcars.com         Home of UK kit cars - madabout-kitcars.com Various kit car write ups All the latest kit car news Kit car related and general discussion

Search
Manufacturers
Kit Cars
Kit Car Data sheets
Picture Gallery
SVA Knowledgebase
Clubs & Communities
Build cost estimator
Kit cars for sale
Knowledge Base 
KitcarUSA.com
Classic-Kitcars.com
 

Go Back   Madabout Kitcars Forum > Mad Build Area > Marlin 5exi builds

Marlin 5exi builds Calling all you sexi builders....sorry 5exi builders, show us your progress.

Reply
 
Thread Tools Display Modes
  #1  
Old 17th May 2020, 10:04
gw302's Avatar
gw302 gw302 is offline
Junior Member
 
Join Date: Mar 2011
Location: West Sussex ~ Petworth
Posts: 26
gw302 is on a distinguished road
Default *rear wishbone failure*

Hi all,

While driving through Cambridge the rear bottom wishbone snapped in half. Thankfully this was at low speeds (20 mph) and both I and the car were not damaged further, the AA also managed to successfully recover the car (the relay option is great).

I'm not sure why this happened yet. My guess is that it has fatigued and I was lucky it went when it did (there wasn't a collision prior to failure). It doesn't appear to be an obvious welding issue as it has broken through the tube and not along the weld line, which makes me wonder if the area needs to be strengthened. A very simplistic structural analysis (attached) confirms that this region is the area of highest stress on the wishbone under acceleration.

Has anyone else had any problems with this? The car is running the latest suspension setup from Marlin.
Attached Images
File Type: jpg IMG_2442.jpg (104.0 KB, 35 views)
File Type: jpg stuctural analysis.jpg (12.7 KB, 30 views)

Last edited by gw302; 17th May 2020 at 11:04..
Reply With Quote
Available from eBay
  #2  
Old 17th May 2020, 11:11
Grey V8 Pete's Avatar
Grey V8 Pete Grey V8 Pete is offline
Senior Member
 
Join Date: Nov 2011
Location: Exeter
Posts: 171
Grey V8 Pete is on a distinguished road
Default

Good job it happened at low speed! I would guess that the crack started along the edge of the weld in the heat affected zone. I would want to replace that flat gusset with a U-section piece, preferably wrapping it around the outer tube as far as possible on replacement components, as you need to suspect the other side of the car is also at risk of failure. So replacing both would be a good idea. I have experienced three failures over the years when accelerating from standstill. Two were half shafts (on a classic car) and one was a diff mount. There is a lot of stress on drive train and suspension components at this time. Peter.

Last edited by Grey V8 Pete; 17th May 2020 at 11:14..
Reply With Quote
  #3  
Old 18th May 2020, 19:10
bigrich's Avatar
bigrich bigrich is offline
Senior Member
Enthusiast
 
Join Date: Nov 2005
Location: Cheshire
Posts: 404
bigrich is on a distinguished road
Default Rear Suspension ?

Hi,

Not seen that failure mode before on an exi. I'm running the original suspension with my own toe control mod but this lower wishbone is still standard. How many miles have you covered? 21k on mine and no signs yet.....I must inspect closely though next time I get her out.

Good it was low speed

Cheers Rich
Reply With Quote
  #4  
Old 19th May 2020, 00:37
gw302's Avatar
gw302 gw302 is offline
Junior Member
 
Join Date: Mar 2011
Location: West Sussex ~ Petworth
Posts: 26
gw302 is on a distinguished road
Default

I'm definitely going to strengthen the lower wishbones. This is actually the second time one has snapped (in exactly the same place). The first was when I was rebuilding the car (engine swap) and I was pushing the bushes out by hand, levering the wishbones against the floor admittedly, but it snapped clean through. Not sure if I just have bad luck with them but I can't think how my setup could be causing this failure!

I also need to mod them while I'm at it: the on-board pick up points mean I have hardly any droop in the suspension at all before the wishbone collides with the bottom chassis rail. The maximum I can jack the car up is to about 110mm at the rear - the suspension travel is then all in compression. I made sure I altered the dampers to the correct length (so the wishbone doesn't actually collide with the frame).

Good to give it an inspection though.

Cheers, George
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +0. The time now is 08:53.

copyright madabout-kitcars.com 2000-2020
terms and conditions | privacy policy