New front wing stays, old ones broke again
The front wing stays rusted and broke again, did a temporary fix a few months ago, but finally it’s time to make some new ones which will hopefully be more resilient to the elements.
Started with two 1 meter 10mm diameter solid rods http://www.msportster.co.uk/wp-conte...5-1024x768.jpg A piece of bar to turn into the bracket that will hold the rod on to the front uprights with a U clamp (51mm u clamp) http://www.msportster.co.uk/wp-conte...6-1024x768.jpg Bracket cut shown with U clamp. http://www.msportster.co.uk/wp-conte...7-1024x768.jpg Test fitted to the uprights http://www.msportster.co.uk/wp-conte...1-1024x768.jpg Used a clamp to hold the round bar to the bracket to get a it roughly lined up. http://www.msportster.co.uk/wp-conte...0-1024x768.jpg Used a caliper to evenly space the round bar away from the alloy wheels http://www.msportster.co.uk/wp-conte...9-1024x768.jpg Held in by hand for a better view of the bracket and round bar http://www.msportster.co.uk/wp-conte...2-1024x768.jpg Tack welded the round bar to the bracket http://www.msportster.co.uk/wp-conte...0-1024x768.jpg My temporary workshop setup – don’t recommend using a workmate for welding due to the risk of burning wood and fire. Use a metal welding table, which I don’t have in my garage. Grabbed the round bar quite far away from the weld so it was fine. Also used a TIG so no splatter. http://www.msportster.co.uk/wp-conte...9-1024x768.jpg I’m still a total amature at welding but these are OK http://www.msportster.co.uk/wp-conte...8-1024x768.jpg The main thing is that is holds together well. The angle grinder hides the bad. http://www.msportster.co.uk/wp-conte...3-1024x768.jpg One of the most time consuming parts of the build was creating a jig so that all four final bends ended up very similar. http://www.msportster.co.uk/wp-conte...4-1024x768.jpg It may only look like two bends, but there are hours of measuing, eyeing up and carefully deciding where the bends need to go. http://www.msportster.co.uk/wp-conte...6-1024x768.jpg The rod lines up with the holes on the carbon wings. http://www.msportster.co.uk/wp-conte...7-1024x768.jpg Now here’s one of those things that happens all too often on a project – the rods ended up 10mm too high on the first go. This is jig MK2 with the height adjusted. It did mean having to straighten out the rod and rebend it to the right position. http://www.msportster.co.uk/wp-conte...2-1024x768.jpg Here’s a test fit of the front of the rod bent into place http://www.msportster.co.uk/wp-conte...1-1024x768.jpg The jig is holding the back up. http://www.msportster.co.uk/wp-conte...4-1024x768.jpg Left to right the mount positions are little way off on the back, so some creative bending and P clip positioning evens out the rod placement. http://www.msportster.co.uk/wp-conte...5-1024x768.jpg The back bent into shape, again two bends took many hours to get to the right position. http://www.msportster.co.uk/wp-conte...3-1024x768.jpg Here are the P clips that will mount the wings to the rod http://www.msportster.co.uk/wp-conte...0-1024x768.jpg First test fit of the driver side, got some really nice new A4 grade cup washers, bolts and nuts from Westfield Fastners to finish it off. http://www.msportster.co.uk/wp-conte...4-1024x768.jpg http://www.msportster.co.uk/wp-conte...9-1024x768.jpg Test fit on the passenger side. The wing was too close to the tyre so this one needed a bit more fine tuning to get it right. http://www.msportster.co.uk/wp-conte...6-1024x768.jpg A view from underneath with the wheel off. http://www.msportster.co.uk/wp-conte...7-1024x768.jpg There is enough gap between the tyre and the carbon, looks quite close from this angle. If there are problems it is easy to tweak the bends to create more clearance. http://www.msportster.co.uk/wp-conte...8-1024x768.jpg Before and after, the before is version 3 of the mounts which also failed eventually. http://www.msportster.co.uk/wp-conte...1-1024x768.jpg Ahh shiny parts! |
Good job , what form of heat did you use for the bends ?
Where you were 10mm off I think I would have cut and shut the straight section especially if you had TIG to hand :badgrin: regards Paul |
Thanks :) I used a yellow MAPP gas container with a blow tourch (it says that's is a replacment for MAPPon the label). The type you get in DIY stores for plumbing. Did the trick pretty well!
If my welding skills were better I'd have considered it, straightening out and rebending was easier for me to do! It added some extra time but most of it was adjusting the templte. The template has some globbed on ali welding on it - now that's something I've only tried one other time, but it was string enough to hold it together for a template. I've spent more time stainless welding as made up a new exhaust last year. |
Good work Paul. Time consuming but very satisfying in the long run.
Liking the MCM stickers and wall covering by the way. Love their show as well as Skid Factory, Binky and recently Nathan’s Garage. Hope they last as the fit and finish deserves that Dave |
Thanks Dave, yeah MCM is up there amoung my fav YT channels. I quite like bad obession motorsport too. Also Roadkill, Roadkill Garage and Hotrod Garage but those are now behind the motortrend paywall. The 3rd party content they've licensed for the UK has gotten a lot better recently, to start with it was mostly only their own content.
|
Good write up as usual Patrick, I have a similar very jury rigged setup with a U Clamp holding the original stays in place but looks like the welds on those have failed again.
Can I ask what failed on version 3 out of curiosity? Andy |
Thanks Andy! On the last mild steel version the part that bends up and over the tyre had rusted, fatigued and broken off. That's why you see a bit of damage on the carbon where it impacted the tyre and locked the front wheel up.
I'd perhapse consider welding a bracket to the upright to bolt it to on a future version but that would have needed a lot more disassembly. The u clamp factory style mount works well enough when bolted up tight |
Just looked at your pics again and doesn't look like your uprights are thecsame as mine, is yours not an E36 front suspension?
|
The uprights are modified E30 uprights - on the E30 the shock is mounted inside the upright which is a tube design - they chopped the top of the tube and weld in an insert with a thread for a metro ball joint, the factory mount design used the U bracket very similar to what I recreated:
https://www.realoem.com/bmw/enUS/sho...diagId=31_0143 On the E36 the shock is bolted from the back, I don't remember what the upright design looks like on the E36 version but I'll likey a bit different. https://www.realoem.com/bmw/enUS/sho...diagId=31_1252 |
One solution with wing stays (if they are breaking near a weld) is to braze joints rather than weld them - this has been used successfully on bicycles for over 100 years. I know some will say 'lugged joints', but there are also thousands of lugless frames out there as well - VERY thin tubes taking huge forces (think front forks, the ends are a simple brazed joint consisting of a plate in a slot!)
All to do with the heat affected zone....... when welding takes place the metal near the weld can be adversely affected by the heat, causing it to break - the heat of brazing is much lower. |
Cycle wings tend to flap about and resonate unless the brackets are really heavy duty and solid. The only solution on the Lotus 7 style cars I've owned is to make the brackets from over size material which solved the problem in the end !
|
Quote:
quite oversized. No issues after doing that. (learned after three attempts). |
Quote:
The benefit of brazing is that a large diameter (but thin-walled) tube can be used, which may be no heavier that the original solid bar, but will be more rigid - the light tube will be durable enough using the brazing process. |
Quote:
|
Not 100% relevant, but this is how it's done on my Pembleton. The stays are made by a guy in Belgium who started off making them for the Lomax but now makes them for any 2CV based kit.
As you can see the diameter of the actual stays is quite small (9mm?) but the important bit is the triangulation (6mm) which stops any flexing and vibration - the killer for wing stays. Cheers, Robin https://live.staticflickr.com/65535/...3732c484_b.jpgwing_stay by Robin Martin, on Flickr |
Those look nice and sturdy, much more triangulation and a larger mount surface. I could extend my mounting plate adding a second U bolt and some triangulation.
|
Very nice.
|
All times are GMT +0. The time now is 10:30. |
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright Madabout Kitcars 2022