|
Vintage and Classic Roadster Kit Car Builds For Vintage and Classic era kit cars. Post your build reports, problems and progress here |
12th July 2020, 04:33
|
|
Senior Member
|
|
Join Date: Feb 2012
Location: Wembley, London
Posts: 5,058
|
|
Looking more complete every time.
|
17th July 2020, 17:41
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
finally got a petrol tank so set about making a cradle to hold it in while trying to keep it low in the boot. the boot is a good size in these because it should be the engine and I want to keep as much of it as possible.
IMG_20200717_130748.jpg
IMG_20200717_152522.jpg
IMG_20200717_152527.jpg
Now the tank is in I can start forming the boot floor and walls, from the inside its starting to look like a car.
IMG_20200717_152505.jpg
IMG_20200717_152535.jpg
made a center tunnel to cover the gearbox and split it so it easily comes out easy also formed the rear seat still needs a lot of work . and yep I do need some more fiberglass
|
19th July 2020, 07:38
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
Cardboard and lino are out so it must be time to start on the boot,the hover box has a glossy wax coating brill for glassing it dose not stick. bit of very basic framework to hold it all in place 3 lairs of 600 csm and a lair of woven and we have part of a boot and wheel arches.
IMG_20200718_091110.jpg
IMG_20200718_095516.jpg
IMG_20200718_101636.jpg
IMG_20200718_171403.jpg
I am going to run out of resin already used my 5th tin this year, plan is to get as much as I can in with just one lair of csm then when I have more resin thicken it all in one hit
|
19th July 2020, 15:07
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
I have made a fiberglass cover for the tank to protect all the vitals loads of tape and cardboard should just pull off when its all hard. just need to trim it down and tech screw it in place so I can always get at the tank.
IMG_20200719_124810.jpg
IMG_20200719_144134.jpg
car will have a lovely rear end when its all finished lol;
IMG_20200719_145844.jpg
|
26th July 2020, 07:41
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
I needed an ignition switch but it was just as cheap to buy a complete power steering column off a corsa so we now have power steering. Need to change the steering wheel but not sure stock bug or chrome and wood.
IMG_20200725_155958.jpg
IMG_20200725_160002.jpg
good week on ebay bought a set of wheel adapters 40quid so I can look at getting the wheels on. Plus a full roll of core mat and two 25l tins of resin 90 quid always worth scanning fleby for anything close. should have my ZGT for September so that will be a busy month for now going fishing so no action till then.
|
27th July 2020, 06:42
|
|
Senior Member
|
|
Join Date: Jul 2011
Posts: 5,328
|
|
Wow, such fast progress is making me dizzy! I take it the Corsa column has electric power assistance rather than hydraulic? Would be a nice mod for a six-pot car on wide tyres, are there any issues connecting it to the rack?
|
27th July 2020, 08:02
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
yep electric power assistance they sell controllers on flebay around £15 from memory its like a volume button more power more assistance. all lines up bang on using part mx5 in the middle. I fitted one on my Chevy they work a treat and are as cheap as chips
|
31st August 2020, 16:33
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
evening all well I am back off my hols my Zgt is going to be a while yet so some more time on the speedster. wheel spacers have arrived so I fitted the wheels I must have done something right they are bang on for distance from the arch both sides. I am not 100% happy with the area in blue I made it flatter first. Then changed it to what you see still not 100%
IMG_20200831_161324.jpg
so now wondering should I go whole hog and put a roof on it. it would make it more usable and they are just as cool with a roof ,,,any thoughts anyone
IMG_20200831_161346.jpg
IMG_20200831_161403.jpg
IMG_20200831_161352.jpg
|
31st August 2020, 21:58
|
Senior Member
|
|
Join Date: Jun 2015
Posts: 1,401
|
|
My vote goes for the coupe. Speedster windscreen won't work with it though.
|
1st September 2020, 06:14
|
|
Senior Member
|
|
Join Date: Jul 2011
Posts: 5,328
|
|
Wheels look great, the rear 'hump' does look closer to the 911 cabriolet than the 356 but, based on what you've achieved so far, it shouldn't take too much work to flatten its curve.
Coupe would look great but sourcing and matching all the side glass and rear screen with frames and trim could become an expensive pain.
Keep up the good work!
|
1st September 2020, 19:59
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
ok so I do fancy a coupe but need to think glass first VW beetle 1303 has a curved screen but I think it will be to high. shame I can get a full set of stock glass flat screen for £70 not to far away. Morris minor back window looks more in proportion easy to get just need to find one I can measure. MGB frame with glass but I think to straight.side and rear not so much a problem its getting the front right so any others I could look at.
OutlawPorsche2.jpg
split screen still has a curve on the edges so would it still work with just flat glass and look as good
emory-motorsports-1960-porsche-356-rsr-merges-the-356-with-components-of-a-964_100704934_h.jpg
loving the flat bonnet look too but dont think it would cover the engine big bump with a vent maybe now that would spark questions lol
Last edited by andysharrock; 2nd September 2020 at 13:10..
|
1st September 2020, 20:14
|
|
Senior Member
|
|
Join Date: Sep 2011
Posts: 1,446
|
|
The speedster clinic were selling a speedster hardtop maybe go that route ?
|
2nd September 2020, 06:16
|
|
Senior Member
|
|
Join Date: Jul 2011
Posts: 5,328
|
|
I tried to buy some parts from the Speedster Clinic a year or two back. The order wouldn't go through on their website and I couldn't get a response from them from their contact details.
If you can get hold of them and they are still trading they'd be a great source of parts at reasonable prices in the UK.
|
2nd September 2020, 08:33
|
|
Senior Member
|
|
Join Date: Sep 2011
Posts: 1,446
|
|
It’s where Andy got his bodywork sides still trading and selling kits
|
2nd September 2020, 09:31
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
yep they are still trading Gary is whom the part body came from. I was going to pop down and see some of his kits to give me a idea of which way to go see one in the flesh. Not a big fan of the removable hard top just always look like an add on.with a coupe same as in the 250swb the lid makes a massive difference and is what makes the car so cool. decision decisions
Last edited by andysharrock; 2nd September 2020 at 13:10..
|
6th September 2020, 07:02
|
|
Senior Member
|
|
Join Date: Jul 2011
Posts: 5,328
|
|
Wow, that profile's looking quite 356/911 hybrid. Could also pass for an early streamliner, I like it!
|
6th September 2020, 08:02
|
|
Senior Member
|
|
Join Date: Jun 2011
Location: sheffield
Posts: 564
|
|
thanks for the positive comments Mr t, I am not trying to copy anything going very much by eye and what I think will look right. The proof will be when I get some fiber glass on it and open the windows up . that's today's job front screens will be flat glass. In fact I have planed it right it will all be flat glass so that will make windows easy.
13047955.jpg
|
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +0. The time now is 04:18.
|