|
Marlin Sportster, Cabrio, Berlinetta and Roadster builds Enthused or Confused about your vintage Marlin build? Ask away here or show off your build. |
18th June 2009, 15:12
|
|
Senior Member
Enthusiast
|
|
Join Date: Sep 2004
Posts: 1,891
|
|
Tonneau
Does anyone have any pictures of the Sportster tonneau? I just received mine from Marlin and there doesn't seem to be any cut-out at the back to take into account the roll bar. I could just be being a bit thick but there are no instructions for fitting which doesn't help.
Also the centre zip is fitted at an angle so that it starts at the centre at the back and then angles towards the drivers side. By the time it reaches the front the panel is only about 12 inches wide. (I will post a picture later) I am sure there is a reason for this but I can't think what at the moment.
On the plus side it looks well made and is supplied with good fixings (lift-the-dot rather than the cheaper press stud things you sometimes get)
Robin
|
18th June 2009, 15:25
|
|
Senior Member
|
|
Join Date: Apr 2009
Location: Somerset
Posts: 518
|
|
Just a thought, if the vehicle needs to go through IVA the lift-the-dot fasteners will be a big fail point!
|
19th June 2009, 07:47
|
|
Senior Member
Enthusiast
|
|
Join Date: Sep 2004
Posts: 1,891
|
|
Thanks Peter
The Marlin Tonneau looks like the one on the red car. It's in three parts with the centre zip offset towards the driver at the front. (Mine doesn't have the headrest pods) I spoke to Terry and she confirmed it should have cutouts for the roll bar. Marlin have the covers made by a 3rd party so it's not really their fault other than perhaps they should have checked it before it was sent out.
Apparently Marlin are now away for two weeks so they have given me the name of a contact at their supplier so I can try and get it sorted.
Life is never simple.....
Robin
|
25th June 2009, 23:02
|
Senior Member
Enthusiast
|
|
Join Date: Jan 2005
Posts: 148
|
|
Would be keen to hear your results - I bought one over the winter from Marlin not thinking that it needs to be warm when fitting else it will sag.
I asked about the cutout and Mark told me I need to cut the tonneau around the roll bar myself.
I haven't figured out how to put the fastenings onto the tonneau yet....
Andy
|
26th June 2009, 07:52
|
|
Senior Member
Enthusiast
|
|
Join Date: Sep 2004
Posts: 1,891
|
|
Personally I wouldn't want to make the roll bar cutouts myself. The material has to be reinforced by being doubled up and stitched - not really a DIY job. I spoke directly to the manufacturer and they said to send it back directly to them - which I have done. It will be interesting to see the results....
When I spoke to Lang & Potter (who make the Tonneau) they told me that they had the pattern for the cutouts - but their seemed to be some confusion between them and Marlin as to if they were standard.
Hmmmm.......
Robin
PS - I beleive that there is a tool that you can buy to fit the bits to the tonneaue - but it is expensive.
|
26th June 2009, 08:20
|
|
Senior Member
Enthusiast
|
|
Join Date: Feb 2005
Location: Hampshire
Posts: 2,496
|
|
What are their details?
|
26th June 2009, 11:15
|
|
Senior Member
Enthusiast
|
|
Join Date: Feb 2005
Location: Hampshire
Posts: 2,496
|
|
excellent thanks
|
1st July 2009, 21:54
|
Senior Member
Enthusiast
|
|
Join Date: Jan 2005
Posts: 148
|
|
Hows the tonneau going Robin?
|
2nd July 2009, 07:47
|
|
Senior Member
Enthusiast
|
|
Join Date: Sep 2004
Posts: 1,891
|
|
Still at L & P having the roll bar cut-outs made. Supposed to get it back by tomorrow but I am not holding my breath. Fortunately I haven't paid for it yet....
I will post up some pictures once it has returned.
Robin
|
2nd July 2009, 21:56
|
|
Senior Member
Enthusiast
|
|
Join Date: Mar 2005
Posts: 3,075
|
|
Quote:
Originally Posted by MartinClan
Still at L & P having the roll bar cut-outs made. Supposed to get it back by tomorrow but I am not holding my breath. Fortunately I haven't paid for it yet....
I will post up some pictures once it has returned.
Robin
|
Actually, they were pretty fast getting me my right size hood so you may be surprised!
|
3rd July 2009, 08:37
|
|
Senior Member
Enthusiast
|
|
Join Date: Sep 2004
Posts: 1,891
|
|
A question for Peter....
A question for Peter....
When fitting the "Lift the dot" fixings on your hood did you use the special tool - or did you improvise?
Robin
|
16th August 2009, 09:21
|
|
Senior Member
Enthusiast
|
|
Join Date: Feb 2005
Location: Hampshire
Posts: 2,496
|
|
As you know I don't have a hood but I did try to fit my tub scientifically using a tape measure. I gave up pretty quickly as both the chassis and the tub are not symmetrical, so I would guess that will translate into a wonky hood as well!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Thread Tools |
|
Display Modes |
Hybrid Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +0. The time now is 19:46.
|