|
Vintage and Classic Roadster Kit Car Builds For Vintage and Classic era kit cars. Post your build reports, problems and progress here |
30th October 2015, 19:10
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Up-dating my McCoy
In the beginning
I first heard from a friend about the car, he told me that a friend of his was selling a mini based kit car but couldn’t give me any details of it, I arranged to go and view the car thinking it may be a Mini Midas or similar but when I first saw it, it reminded me of a car I was familiar with from the 70’s, the Clan Crusader but it didn’t look quite right and I knew the Clan had an Imp engine, looking around it had stick on letters saying McCoy which then I was not familiar with, I asked the price, he told me £200 and I gave him the money. It wasn’t running very well so I organised a trailer to get it home.
I got the trailer and went to collect the car to bring it home…
The next day I had a good look over the car and didn’t look too bad but had mechanical issues which I decided it was time for an overhaul, engine, gearbox rear sub-frame, the usual mini problems and later purchased a donor mini.
The interior was shabby but nothing that couldn’t be improved.
|
30th October 2015, 20:05
|
Senior Member
|
|
Join Date: Jun 2011
Location: birchington, kent
Posts: 1,769
|
|
carry on, I'm enjoying this....
|
30th October 2015, 20:15
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Stripping out
I had the car a few years before serious work was started, women’s requirements got in the way, you know what I mean, get married fix up house, move, fix up house etc etc….
Well I got the car on the 20th January 2004 so work out how much time I havn’t been able to get on with it.
Anyway, I was helping my eldest son put a Vtec Honda engine into his mini but he wasn’t putting enough effort into it due to him working 50 miles from home and it looked like I was going to do it for him, there he was wrong, I had other thoughts, I gave him a deal which let me have all the parts he had for the Vtec conversion which I could then put into the McCoy but I never made the deal until we had the engine running because a lot of work would be needed to get it to fit the McCoy and I wasn’t prepare to cut the car to get it to fit with knowing it was a runner.
In the mean time in slow time I started stripping out the McCoy to fit the parts from the donor mini just in case.
This had to come out….
and this along with several other parts that had seen better days…
The engine bay was stripped and cleaned…
On doing this showed a problem with the firewall suffering from heat off the mini exhaust, that would need repairing…
The door cards were removed along with the rest of the interior and the part have been stored until I get back to them.
The fuel tank would also need some work….
None of this would be needed as I would be fitting a beam axle with new swinging arm assemblies that my son had got new for the mini, but I would refurbish the swinging arms as spares…
This lot had to go… and it would become apparent that the front valance would need cutting to allow the Vtec exhaust to fit.
I am not sure what my son was thinking here but I think it would probably be ‘This will be a monster with my Vtec in’
|
30th October 2015, 20:41
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The engine inspection
I said to my son ‘It would be a good idea to inspect the engine before we bench tested it’ because it was bought off E-Bay and collected from the back of a van somewhere in London and we didn’t have any history of it. All he knew that the engine was from a Honda Del Sol and it was a 1.6 B16A2 Vtec unit with gearbox.
We emptied the sump and with horror about a litre of water came out with the oil and sludge, so the sump was to be removed for further investigation
On removal of the sump the bottom end looked surprisingly clean but the sump itself was full of sludge.
The small amount of emulsified oil was removed….
The main and big end bearing shells and crank were inspected and only a small score was found on one of the shells..
So all was cleaned and rebuilt..
While the engine was out a new clutch assembly was fitted along with a new timing belt and tension pulley.
Last edited by pompeyal; 30th October 2015 at 22:14..
Reason: .
|
30th October 2015, 21:14
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Sub-frame build
Last edited by pompeyal; 30th October 2015 at 22:16..
Reason: .
|
30th October 2015, 21:41
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Engine bench test
Heath Robinson would have liked this, I pulled a bench out into the garden and clamped the sub-frame, complete with engine and mini fuel tank a radiator and wiring harness, stuffed an old silencer into the manifold with fire gum attached a battery and tried to fire it up…
Go here for first trial video https://www.flickr.com/photos/383774...7658176284393/
The problem was the immobiliser within the ecu, the steering column was from a different car than the ecu, so the internet was called for, I went searching for possible solutions and it came up trumps, a guy on a Honda forum described in depth on how to by-pass the immobiliser circuits in the ecu, this meant opening it up cutting a couple of resistors out and putting in a few links, after doing this, this is what happened next
Go here https://www.flickr.com/photos/383774...7658176284393/
Last edited by pompeyal; 30th October 2015 at 22:18..
Reason: .
|
30th October 2015, 21:45
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Well that's the first 5 episodes of 27 to date, more to come, watch this space....
Last edited by pompeyal; 31st October 2015 at 08:46..
Reason: .
|
31st October 2015, 11:36
|
Senior Member
|
|
Join Date: Apr 2014
Posts: 198
|
|
Excellent, thanks for putting all this effort into the thread a most pleasant surprise when I logged on. That swage tool is a work of art you should hire it out, I followed a McCoy last week they look better as they get older Ed
|
31st October 2015, 12:50
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Hi Ed, I thought I should as I have been teasing for a while, I don't think you will reckonise mine when its finished, if you see that McCoy again would you mind taking its reg no as I am trying to make a database on them, cheers..
|
31st October 2015, 13:10
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Rear end
Now for the back, the old sub-frame was in serviceable condition believe it or not but not for me, I wanted to use the beam axle my son had for his mini, the problem with these after market items they do no cater for everything and the beam was no different, it did not have provision for the handbrake cables so as its what I do I made that right…
Having that sorted the beam was drilled for fit and powder coated..
The beam was offered up and centralised, the car drilled and then bolted into place, I will be strengthening the heal plate it fits to later…
Nice new coil overs..
Refurbished swinging arms with new brake parts and bearings were then fitted to the beam, all the geometry will be set up at a later date..
I was going to have it sit on revolution 12” wheels…
But decided on these 13” Starmags..
The problem with all McCoy’s they sit high in the arch at the rear, even using hi-lo coil overs, I have thoughts on righting that later.
|
31st October 2015, 13:35
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Rear Lights
Last edited by pompeyal; 31st October 2015 at 17:47..
Reason: .
|
31st October 2015, 13:46
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The boot lid
Next was the boot lid, first thing was to flat back and fill the hole that some previous owner drilled for a hideous ill fitting spoiler, maybe he liked it but not my cup of tea, I have other plans on that front and I am considering integrating an air brake…hehe
A few coats of primer..
And a couple of top and that will do for the time being..
|
1st November 2015, 14:35
|
Junior Member
|
|
Join Date: May 2012
Posts: 7
|
|
I'm liking this resto/conversion.
Alec
|
1st November 2015, 15:09
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Thanks Alec more coming....
|
1st November 2015, 15:10
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
Throttle
The throttle peddle was the next to be sorted as I was using a Honda cable and due to where the engine sub-frame covered the original cable hole for the mini I had to re-position the hole to miss the sub-frame
As the Fibre glass was thicker than the steel firewall from the Honda I manufactured a carbon-fibre interface plate
The the peddle needed to be altered to suit the new cable position
The peddle then was warmed and bent upwards to achieve enough travel but not so the it sat above the brake peddle
The engine was refitted into the car and the cable run in
The throttle body was the fitted and the throttle was tested for full travel
All good there
|
1st November 2015, 16:40
|
Senior Member
|
|
Join Date: Apr 2014
Posts: 198
|
|
Your exhaust routing idea and cut section weld techniques for the bends are as inspired as your steering spline mod.
The McCoy I saw was in Brighouse west Yorkshire travelling with a hard top quantum and a mustard coloured allegro towards hebden bridge so they probably came off the M62 so could of been from anywhere. It was odd because when the quantum came out I recall drooling over it particularly the use of Sierra sapphire back lights but yet now it looked very dated and the rear lights looked massive whereas the McCoy looked more like a traditional yet very small sports car lotus élan esque.Ed.
Last edited by a big scary monster; 1st November 2015 at 16:43..
|
1st November 2015, 17:01
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The Throttle body
I now discovered a major problem, the throttle body inlet was looking straight at the clutch master cylinder, now that’s not good, I had a few options here, I could either buy a set of individual throttle bodies or go the hard way and modify the one I had..
Well a challenge it was then, there seems to be a theme going on here, if I can go the hard way then that’s the way to go, my thoughts on these things are, anyone with enough money can go and buy all the nice new goodies and bolt them on but I wanted to make this mine so the modification was the way to go.
So here goes (Caution: this part of the build took some time and I want to thank both my welder colleagues for all the work they put in for me here)
First things first, I need to cut and shut the ports to allow the throttle body and chamber to lift up and forward away from the clutch master cylinder, I decided where to cut and then machined both the cut faces flat and square.
After I checked the measurements and angles of the machined part, incase I needed to make further changes after a trial fit.
After checking there became a mismatch of the ports, this was expected and I was going to put in spacers later to compensate for the errors
A trial fit was done and the spacer thickness was determined
Once knowing the thickness the angle for each spacer was measured
Then I manufactured them
Once made all was cleaned and this is where my welders made it all come together, after lots of cursing of course
One side done….now for the other half
|
1st November 2015, 17:17
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The Throttle body (cont’d)
Last edited by pompeyal; 1st November 2015 at 17:35..
Reason: .
|
1st November 2015, 17:33
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The Throttle body (cont’d)
After fettling a bit more from the fuel rail to allow for the throttle movement the was on last thing to do..
The brake vacuum take of pipe was facing in the wrong direction
So after gently heating the casting around the pipe I managed to rotate it to the required direction
Now it was completely assembled and ready to fir to the engine..
Happy with that…
|
1st November 2015, 17:57
|
|
Senior Member
Enthusiast
|
|
Join Date: Jun 2008
Location: Fareham, Hants
Posts: 161
|
|
The wiring harness
I acquired a complete Honda harness that I was going to modify to suit the McCoy, It was a harness from a civic so I would have quite a few bits to cut out, first I took the rear harness and rebuilt that, removing the electric window wiring and anything else I didn’t require
Then I started to fit the engine harness and the engine bay harness for the lights etc, this I would cut about removing unwanted bits later.
The parts of the harness I didn’t need were the ABS, Air con etc
I made drawings of the wiring and what was for what, labelled all the ends and then it was ready for stripping, I didn’t want to do that yet because I didn’t know what was required for the ecu, so I started the cabin wiring (Warning: If you have a nervous disposition look away now)
Well if you can make any sense of that lot without getting a head ache please come and sort it out because it has done my head in, I won’t let it beat me but I will be doing it in stages, it had taken an age to get here, looking through wiring diagrams, sorting out what is needed, what may be needed, what isn’t needed or of it was effected by what had been or was going to be cut out…..Hmmmm, needless to say I have left this alone for a while now to get my sanity back
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +0. The time now is 02:22.
|